- FAILED TO LOAD MODULE CANBERRA GTK MODULE GVIM UBUNTU 19.10 INSTALL
- FAILED TO LOAD MODULE CANBERRA GTK MODULE GVIM UBUNTU 19.10 FREE
Lrwxrwxrwx 1 root root 17 Jul 9 16:14 /etc/os-release -> pop-os/os-release Libcanberra-gtk-module set to manually installed.Īnd, when I check to see if there are odd permissions on /etc/os-release I see this: ls -lh /etc/os-release Libcanberra-gtk-module is already the newest version (0.30-7ubuntu1). Libcanberra-gtk3-module set to manually installed.
FAILED TO LOAD MODULE CANBERRA GTK MODULE GVIM UBUNTU 19.10 INSTALL
When I try to install canberra-gtk-module is loaded I see this: libcanberra-gtk3-module is already the newest version (0.30-7ubuntu1). The splash page loads, but it never gets past that. Gtk-Message: Failed to load module "canberra-gtk-module" Now, when I run gitkraken in the console I get this error: Gtk-Message: Failed to load module "canberra-gtk-module" I used snap to install it with this command: RuntimeError: Process 18969 for /Kernel/Session not foundĪny guidance would be helpful.I am trying to install GitKraken on a System 76 computer that comes with Pop_OS! installed. Raise RuntimeError, "Process %d for %s not found" % (thePID,theName) Session=clt.waitNSPID("/Kernel/Session",mySessionServ.PID,SALOME.Session)įile "/home/kumar/salome_meca/V2018/modules/KERNEL_V8_5_0/bin/salome/orbmodule.py", line 174, in waitNSPID Warning: this type (SALOME_MED/MEDCouplingFieldDoubleCorbaInterface,objref) already exists, it will be ignored.įile "/home/kumar/salome_meca/appli_V2018/bin/salome/runSalome.py", line 633, in useSalomeĬlt = startSalome(args, modules_list, modules_root_dir)įile "/home/kumar/salome_meca/appli_V2018/bin/salome/runSalome.py", line 578, in startSalome LibGL error: failed to load driver: swrast LibGL error: unable to load driver: swrast_dri.so LibGL error: unable to load driver: i965_dri.so Searching /Kernel/Session in Naming Service +++Gtk-Message: 20:18:22.922: Failed to load module "canberra-gtk-module" Searching Naming Service + found in 0.1 seconds
FAILED TO LOAD MODULE CANBERRA GTK MODULE GVIM UBUNTU 19.10 FREE
Searching for a free port for naming service: 2814 - OK P = Popen(cmd, stdout=PIPE, stderr=STDOUT)įile "/home/kumar/salome_meca/V2018/prerequisites/Python-2710/lib/python2.7/subprocess.py", line 710, in _init_įile "/home/kumar/salome_meca/V2018/prerequisites/Python-2710/lib/python2.7/subprocess.py", line 1335, in _execute_child RunSalome running on kumar-HP-Pavilion-dv6-Notebook-PCĮrror when trying to access active network connections.įile "/home/kumar/salome_meca/appli_V2018/bin/salome/PortManager.py", line 111, in _isNetworkConnectionActiveOnPort I started salome again by defining python 2.7 and I am getting the error as export alias unset export. Print "ERROR: unexisting configuration/environment file(s): " + ', '.join(unexisting) salome and I am getting below following error.įile "/home/kumar/salome_meca/appli_V2018/.salome_run", line 41
However, the application is not launching! I tried to launch the application from the. I followed your suggestion and now the installation was good. I suggest you set the following before running the Salome-Meca installer (quick and dirty):Īlias python=/usr/bin/python2.7 (or whatever is the name of your Python2 executable) It seems like the system Python is being superseded by your custom installation. I installed Salome meca based on the below following comment given by Mr.Thomas